WWA Info Exchange

For Woodworkers By Woodworkers
It is currently Tue May 07, 2024 5:07 pm

All times are UTC - 5 hours




Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Thu May 13, 2010 10:24 pm 
Offline
Veteran
User avatar

Joined: Fri May 12, 2006 9:37 pm
Posts: 5398
Location: Tucson, AZ
Well, the end of the school year has come around and that means teachers pens for my boys' teachers and pens for the assistants... (along with a gift card for a meal out... it never ceases to amaze me that our teachers get paid so little and are so dedicated)

At any rate, this year I used my Carvewright to personalize things a bit--
Image

The top holder is maple with a couple of coats of spray laquer (holy cow it dries almost as fast as you can put it on!)

The bottom holder is lyptus with a shellac and then laquer finish (again, finishing for the 2 pieces was less than 2 hours for several coats to completely dry)

The teachers pen is bloodwood and walnut with a spalted tamarind middle. The other teachers pen is on the lathe-- I'm waiting for the CA to completely cure before removing it.

The bottom two pens are for the TA's and are dymondwood

I think I may have finally figured out how to do a pen holder that I am happy with-- I used a 3/4 forstner bit to create a hollow for a rare earth magnet to be glued on the back, then used the center spur hole as a guide for the 3/16 drill bit at a slight angle... the nibs are (slightly) attracted to the magnet and the pen pulls out without effort but sits nicely in the hole without slipping when you put it in. It also seats itself with a rather satisfying "click" when you set the pen in the hole... I cannot begin to tell you how long I've been searching for an inexpensive way to create a pen holder-- this is my most successful attempt so far-- smaller magnets don't hold with any power at all (as it is, the hold is very minimal) and creating a differently sized hole does not allow a pen nib to register without allowing the pen to tilt too much... the combination of 3/16 hole, 3/4 magnet, and 1/2 material seem to work out just right.
Image
Image
Thanks for looking
Lawrence

Thanks for looking-
Lawrence


Top
 Profile  
 
 Post subject:
PostPosted: Fri May 14, 2010 12:02 am 
Offline
Veteran
User avatar

Joined: Mon Apr 10, 2006 5:34 pm
Posts: 836
Location: Elk Grove,CA
Very nice Lawrence, Teachers and staff will love them. :-D

_________________
I said to Orv and Wil many times this sucker will fly
Tom Taylor


Top
 Profile  
 
 Post subject:
PostPosted: Fri May 14, 2010 8:42 am 
Offline
Veteran

Joined: Sun Nov 13, 2005 5:23 pm
Posts: 2796
Location: Montgomery,Alabama. USA
Nice work, Lawrence.

_________________
My Boss is a Jewish Carpenter!


Top
 Profile  
 
 Post subject:
PostPosted: Fri May 14, 2010 10:14 am 
Offline
Veteran
User avatar

Joined: Mon Aug 27, 2007 4:15 pm
Posts: 1542
Location: Belleair, FL
Your teachers are very lucky. I doubt many other parents are this thoughtful. And it's really nice work you've done as well.


Top
 Profile  
 
 Post subject:
PostPosted: Mon May 17, 2010 9:29 am 
Offline
Veteran
User avatar

Joined: Wed Jun 16, 2004 12:01 am
Posts: 9296
Location: Aurora CO
Nice work Lawrence. I really like the idea of using a magnet to keep the pen upright in the hole. 8)

_________________
Frank
WWACOAUX#1
"I love the smell of Sawdust in the morning, it smells like, victory." Image
WWA'ers I've met: Popeye, Ed Avery, Stephen Wolf, Rockfish, Rodedon


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group